锁相放大器是一种对交变信号进行相敏检波的放大器。它利用和被测信号有相同频率和相位关系的参考信号作为比较基准，只对被测信号本身和那些与参考信号同频（或者倍频）、同相的噪声分量有响应。因此，能大幅度抑制无用噪声，改善检测信噪比。此外，锁相放大器有很高的检测灵敏度，信号处理比较简单，是弱光信号检测的一种有效方法。　　锁相放大器的用途主要用于检测信噪比很低的微弱信号。即使有用的信号被淹没在噪声信号里面，即使噪声信号比有用的信号大很多，只要知道有用的信号的频率值，就能准确地测量出这个信号的幅值。 　　本例中的电路采用Analog Devices公司的AD630平衡调制解调IC实现了一种简单的低成本锁入放

a AD630 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 © 2004 Analog Devices, Inc. All rights reserved. REV. E Balanced Modulator/Demodulator FUNCTIONAL BLOCK DIAGRAM CM OFF ADJ CM OFF ADJ DIFF OFF ADJ DIFF OFF ADJ 6 5 4 3 2.5k AMP A 2.5k AMP B –V 10k 10k 17 5k 8 9 10 COMP 19 18 1 15 7 16 14 13 11 12 RINA CH A+ CH A– RINB CH B+ CH B– SEL B SEL A 2 20 COMP +VS VOUT RB RF RA CHANNEL STATUS B/A –VS AD630 A B PRODUCT DESCRIPTION The AD630 is a high precision balanced modulator that combines a flexible commutating architecture with the accuracy and temperature stability afforded by laser wafer trimmed thin film resistors. Its signal processing applications include balanced modulation and demodulation, synchronous detection, phase detection, quadrature detection, phase-sensitive detection, lock-in amplification, and square wave multiplication. A network of on-board applications resistors provides precision closed-loop gains of ±1 and ±2 with 0.05% accuracy (AD630B). These resistors may also be used to accurately configure multiplexer gains of +1, +2, +3, or +4. Alternatively, external feedback may be employed, allowing the designer to implement high gain or complex switched feedback topologies. The AD630 can be thought of as a precision op amp with two independent differential input stages and a precision comparator that is used to select the active front end. The rapid response time of this comparator coupled with the high slew rate and fast settling of the linear amplifiers minimize switching distortion. In addition, the AD630 has extremely low crosstalk between channels of –100 dB @ 10 kHz. The AD630 is used in precision signal processing and instrumentation applications that require wide dynamic range. When used as a synchronous demodulator in a lock-in amplifier configuration, it can recover a small signal from 100 dB of interfering noise (see Lock-In Amplifier Applications section). Although optimized for operation up to 1 kHz, the circuit is useful at frequencies up to several hundred kilohertz. Other features of the AD630 include pin programmable frequency compensation, optional input bias current compensation resistors, common-mode and differential-offset voltage adjustment, and a channel status output that indicates which of the two differential inputs is active. This device is now available to Standard Military Drawing (DESC) numbers 5962-8980701RA and 5962-89807012A. PRODUCT HIGHLIGHTS 1. The configuration of the AD630 makes it ideal for signal processing applications, such as balanced modulation and demodulation, lock-in amplification, phase detection, and square wave multiplication. 2. The application flexibility of the AD630 makes it the best choice for applications that require precisely fixed gain, switched gain, multiplexing, integrating-switching functions, and high speed precision amplification. 3. The 100 dB dynamic range of the AD630 exceeds that of any hybrid or IC balanced modulator/demodulator and is comparable to that of costly signal processing instruments. 4. The op amp format of the AD630 ensures easy implementation of high gain or complex switched feedback functions. The application resistors facilitate the implementation of most common applications with no additional parts. 5. The AD630 can be used as a 2-channel multiplexer with gains of +1, +2, +3, or +4. The channel separation of 100 dB @ 10 kHz approaches the limit achievable with an empty IC package. 6. The AD630 has pin strappable frequency compensation (no external capacitor required) for stable operation at unity gain without sacrificing dynamic performance at higher gains. 7. Laser trimming of comparator and amplifying channel offsets eliminates the need for external nulling in most cases. FEATURES Recovers Signal from 100 dB Noise 2 MHz Channel Bandwidth 45 V/s Slew Rate –120 dB Crosstalk @ 1 kHz Pin Programmable, Closed-Loop Gains of 1 and 2 0.05% Closed-Loop Gain Accuracy and Match 100 V Channel Offset Voltage (AD630BD) 350 kHz Full Power Bandwidth Chips Available 元器件交易网www.cecb2b.com –2– REV. E AD630–SPECIFICATIONS (@ 25C and VS = 15 V, unless otherwise noted.) AD630J/AD630A AD630K/AD630B AD630S Model Min Typ Max Min Typ Max Min Typ Max Unit GAIN Open-Loop Gain 90 110 100 120 90 110 dB ±1, ±2 Closed-Loop Gain Error 0.1 0.05 0.1 % Closed-Loop Gain Match 0.1 0.05 0.1 % Closed-Loop Gain Drift 2 2 2 ppm/°C CHANNEL INPUTS VIN Operational Limit1 (–VS + 4 V) to (+VS – 1 V) (–VS + 4 V) to (+VS – 1 V) (–VS + 4 V) to (+VS – 1 V) V Input Offset Voltage 500 100 500 μV Input Offset Voltage TMIN to TMAX 800 160 1000 μV Input Bias Current 100 300 100 300 100 300 nA Input Offset Current 10 50 10 50 10 50 nA Channel Separation @ 10 kHz 100 100 100 dB COMPARATOR VIN Operational Limit1 (–VS + 3 V) to (+VS – 1.5 V) (–VS + 3 V) to (+VS – 1.5 V) (–VS + 3 V) to (+VS – 1.3 V) V Switching Window ±1.5 ±1.5 ±1.5 mV Switching Window TMIN to TMAX ±2.0 ±2.0 ±2.5 mV Input Bias Current 100 300 100 300 100 300 nA Response Time (–5 mV to +5 mV Step) 200 200 200 ns Channel Status ISINK @ VOL = –VS + 0.4 V2 1.6 1.6 1.6 mA Pull-Up Voltage (–VS + 33 V) (–VS + 33 V) (–VS + 33 V) V DYNAMIC PERFORMANCE Unity Gain Bandwidth 2 2 2 MHz Slew Rate3 45 45 45 V/μs Settling Time to 0.1% (20 V Step) 3 3 3 μs OPERATING CHARACTERISTICS Common-Mode Rejection 85 105 90 110 90 110 dB Power Supply Rejection 90 110 90 110 90 110 dB Supply Voltage Range ±5 ±16.5 ±5 ±16.5 ±5 ±16.5 V Supply Current 4 5 4 5 4 5 mA OUTPUT VOLTAGE, @ RL = 2 kΩ TMIN to TMAX ±10 ±10 ±10 V Output Short-Circuit Current 25 25 25 mA TEMPERATURE RANGES Rated Performance–N Package 0 70 0 70 N/A °C Rated Performance–D Package –25 +85 –25 +85 –55 +125 °C NOTES 1If one terminal of each differential channel or comparator input is kept within these limits the other terminal may be taken to the positive supply. 2ISINK @ VOL = (–VS + 1); V is typically 4 mA. 3Pin 12 Open. Slew rate with Pin 12 and Pin 13 shorted is typically 35 V/μs. Specifications subject to change without notice. 元器件交易网www.cecb2b.com REV. E AD630 –3– THERMAL CHARACTERISTICS JC JA 20-Lead PDIP (N) 24°C/W 61°C/W 20-Lead Ceramic DIP (D) 35°C/W 120°C/W 20-Lead Leadless Chip Carrier LCC (E) 35°C/W 120°C/W 20-Lead SOIC (R-20) 38°C/W 75°C/W ABSOLUTE MAXIMUM RATINGS Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±18 V Internal Power Dissipation . . . . . . . . . . . . . . . . . . . . 600 mW Output Short-Circuit to Ground . . . . . . . . . . . . . . . Indefinite Storage Temperature, Ceramic Package . . . –65°C to +150°C Storage Temperature, Plastic Package . . . . . –55°C to +125°C Lead Temperature Range (Soldering, 10 sec) . . . . . . . . 300°C Maximum Junction Temperature . . . . . . . . . . . . . . . . . 150°C PIN CONFIGURATIONS 20-Lead SOIC, PDIP, and CERDIP 14 13 12 11 17 16 15 20 19 18 10 9 8 1 2 3 4 7 6 5 TOP VIEW (Not to Scale) AD630 RINA RINB CH B+ CH B– CH A– CH A+ DIFF OFF ADJ DIFF OFF ADJ RB RF CM OFF ADJ RA CM OFF ADJ –VS SEL B SEL A +VS COMP VOUT CHANNEL STATUS B/A 20-Terminal CLCC 3 2 1 20 19 18 14 15 16 17 4 5 6 7 8 9 10 11 12 13 TOP VIEW (Not to Scale) AD630 DIFF OFF ADJ CM OFF ADJ CM OFF ADJ CHANNEL STATUS B/A –VS CH B+ RINB RA RF RB DIFF OFF ADJ CH A+ RIN A CH A– CH B– SEL B SEL A +VS COMP VOUT ORDERING GUIDE Model Temperature Ranges Package Description Package Option AD630JN 0°C to 70°C PDIP N-20 AD630KN 0°C to 70°C PDIP N-20 AD630AR –25°C to +85°C SOIC R-20 AD630AR-REEL –25°C to +85°C SOIC 13" Tape and Reel R-20 AD630AD –25°C to +85°C SBDIP D-20 AD630BD –25°C to +85°C SBDIP D-20 AD630SD –55°C to +125°C SBDIP D-20 AD630SD/883B –55°C to +125°C SBDIP D-20 5962-8980701RA –55°C to +125°C SBDIP D-20 AD630SE/883B –55°C to +125°C CLCC E-20A 5962-89807012A –55°C to +125°C CLCC E-20A AD630JCHIPS 0°C to 70°C Chip AD630SCHIPS –55°C to +125°C Chip CHIP METALLIZATION AND PINOUT Dimensions shown in inches and (millimeters). Contact factory for latest dimensions. CHIP AVAILABILITY The AD630 is available in laser trimmed, passivated chip form. The figure above shows the AD630 metallization pattern, bonding pads and dimensions. AD630 chips are available; consult factory for details. CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD630 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. 元器件交易网www.cecb2b.com REV. E AD630 –4– 10 15 5 1 10 100 1k 10k 100k 1M RESISTIVE LOAD () CL = 100pF f = 1kHz CAP IN 5k VO 100pF RL Vi 5k OUTPUT VOLTAGE (V) 0 TPC 2. Output Voltage vs. Resistive Load INPUT VOLTAGE (V) dVO dt (V/s) 60 0 –60 –5 –3 –2 –1 1 4 40 20 –40 –20 –4 0 2 3 5 UNCOMPENSATED COMPENSATED TPC 5. dV dt O vs. Input Voltage 10 18 5 0 5 10 15 SUPPLY VOLTAGE (V) OUTPUT VOLTAGE (V) 15 5k 100pF Vi 5k 2k VO f = 1kHz CL = 100pF 0 TPC 3. Output Voltage Swing vs. Supply Voltage FREQUENCY (Hz) 120 60 0 100 1M 100 80 20 40 10 1k 10k 100k UNCOMPENSATED 10M 0 45 90 OPEN LOOP GAIN (dB) 135 180 COMPENSATED OPEN LOOP PHASE (C) 0 TPC 6. Gain and Phase vs. Frequency FREQUENCY (Hz) 15 10 5 1k 10k 100k 1M RL= 2k CL = 100pF 2k 5k 5k Vi VO 100pF OUTPUT VOLTAGE (V) 0 TPC 1. Output Voltage vs. Frequency FREQUENCY (Hz) COMMON-MODE REJECTION (dB) 120 60 0 1 10 100 1k 10k 100k 100 80 40 20 TPC 4. Common-Mode Rejection vs. Frequency AD630–Typical Performance Characteristics 元器件交易网www.cecb2b.com REV. E AD630 –5– 20mV 500ns 20mV 100 90 10 0% 20mV/DIV (Vo) 20mV/DIV (Vi) TOP TRACE: Vo BOTTOM TRACE: Vi 5k 10k 10k Vi CH A CH B 12 VO 2 20 19 18 13 9 10 14 16 15 TPC 7. Channel-to-Channel Switch-Settling Characteristic 100 90 10 0% 100mV 500ns 50mV 1mV 50mV/DIV (Vi) 1mV/DIV (A) TOP TRACE: Vi MIDDLE TRACE: SETTLING ERROR (A) BOTTOM TRACE: Vo 100mV/DIV (Vo) 12 CH A MIDDLE TRACE (A) 10k 10k VO BOTTOM TRACE TEKTRONIX 7A13 10k 1k 30pF 10k Vi TOP TRACE 2 20 13 14 15 TPC 8. Small Signal Noninverting Step Response 100 90 10 0% 10V 10V 1mV TOP TRACE: Vi MIDDLE TRACE: SETTLING ERROR (B) BOTTOM TRACE: Vo 5s 10V 20kHz (Vi) 1mV/DIV (B) 10V/DIV (Vo) 12 CH A 10k 10k VO BOTTOM TRACE 10k Vi TOP TRACE (B) MIDDLE TRACE 10k HP5082-2811 20 2 13 14 15 TPC 9. Large Signal Inverting Step Response 元器件交易网www.cecb2b.com REV. E AD630 –6– TWO WAYS TO LOOK AT THE AD630 The functional block diagram of the AD630 (see page 1) shows the pin connections of the internal functions. An alternative architectural diagram is shown in Figure 1. In this diagram, the individual A and B channel preamps, the switch, and the integrator output amplifier are combined in a single op amp. This amplifier has two differential input channels, only one of which is active at a time. 15 11 2 20 19 18 17 8 7 12 14 13 9 10 RA 5k 2.5k RF 10k 1 16 2.5k +VS RB 10k SEL B SEL A B/A A B –VS Figure 1. Architectural Block Diagram HOW THE AD630 WORKS The basic mode of operation of the AD630 may be easier to recognize as two fixed gain stages which can be inserted into the signal path under the control of a sensitive voltage comparator. When the circuit is switched between inverting and noninverting gain, it provides the basic modulation/demodulation function. The AD630 is unique in that it includes laser wafer trimmed thin-film feedback resistors on the monolithic chip. The configuration shown in Figure 2 yields a gain of ±2 and can be easily changed to ±1 by shifting RB from its ground connection to the output. The comparator selects one of the two input stages to complete an operational feedback connection around the AD630. The deselected input is off and has a negligible effect on the operation. A B RA 5k RF 10k VO RB 10k Vi 2 20 19 18 13 16 15 14 9 10 Figure 2. AD630 Symmetric Gain (±2) When Channel B is selected, the resistors RA and RF are connected for inverting feedback as shown in the inverting gain configuration diagram in Figure 3. The amplifier has sufficient loop gain to minimize the loading effect of RB at the virtual ground produced by the feedback connection. When the sign of the comparator input is reversed, Input B will be deselected and A will be selected. The new equivalent circuit will be the noninverting gain configuration shown in Figure 4. In this case, RA will appear across the op amp input terminals, but since the amplifier drives this difference voltage to zero, the closed-loop gain is unaffected. The two closed-loop gain magnitudes will be equal when RF/RA = 1 + RF/RB, which will result from making RA equal to RFRB/ (RF + RB) the parallel equivalent resistance of RF and RB. The 5 kΩ and the two 10 kΩ resistors on the AD630 chip can be used to make a gain of 2 as shown below. By paralleling the 10 kΩ resistors to make RF equal to 5 kΩ and omitting RB, the circuit can be programmed for a gain of ± 1 (as shown in Figure 9a). These and other configurations using the on-chip resistors present the inverting inputs with a 2.5 kΩ source impedance. The more complete AD630 diagrams show 2.5 kΩ resistors available at the noninverting inputs which can be conveniently used to minimize errors resulting from input bias currents. RA 5k RF 10k RB 10k Vi VO = – RF RA Vi Figure 3. Inverting Gain Configuration RA 5k RF 10k RB 10k Vi VO = (1+ RF RB ) Vi Figure 4. Noninverting Gain Configuration CIRCUIT DESCRIPTION The simplified schematic of the AD630 is shown in Figure 5. It has been subdivided into three major sections, the comparator, the two input stages, and the output integrator. The comparator consists of a front end made up of Q52 and Q53, a flip-flop load formed by Q3 and Q4, and two current steering switching cells Q28, Q29 and Q30, Q31. This structure is designed so that a differential input voltage greater than 1.5 mV in magnitude applied to the comparator inputs will completely select one of the switching cells. The sign of this input voltage determines which of the two switching cells is selected. 20 11 3 4 5 6 2 19 18 13 12 SEL A SEL B DIFF OFF ADJ DIFF OFF ADJ CM OFF ADJ CM OFF ADJ COMP Q74 Q44 CH A– CH A+ CH B+ CH B– i55 Q3 Q4 Q28 Q31 Q30 Q32 C122 C121 i22 i23 –VS VOUT i73 Q52 Q53 +VS Q65 Q33 Q34 Q62 Q35 Q36 Q67 Q70 Q24 Q25 Q29 10 9 8 Figure 5. AD630 Simplified Schematic 元器件交易网www.cecb2b.com REV. E AD630 –7– The collectors of each switching cell connect to an input transconductance stage. The selected cell conveys bias currents i22 and i23 to the input stage it controls, causing it to become active. The deselected cell blocks the bias to its input stage which, as a consequence, remains off. The structure of the transconductance stages is such that it presents a high impedance at its input terminals and draws no bias current when deselected. The deselected input does not interfere with the operation of the selected input ensuring maximum channel separation. Another feature of the input structure is that it enhances the slew rate of the circuit. The current output of the active stage follows a quasi-hyperbolic-sine relationship to the differential input voltage. This means that the greater the input voltage, the harder this stage will drive the output integrator, and the faster the output signal will move. This feature helps ensure rapid, symmetric settling when switching between inverting and noninverting closed loop configurations. The output section of the AD630 includes a current mirrorload (Q24 and Q25), an integrator-voltage gain stage (Q32), and a complementary output buffer (Q44 and Q74). The outputs of both transconductance stages are connected in parallel to the current mirror. Since the deselected input stage produces no output current and presents a high impedance at its outputs, there is no conflict. The current mirror translates the differential output current from the active input transconductance amplifier into single-ended form for the output integrator. The complementary output driver then buffers the integrator output to produce a low impedance output. OTHER GAIN CONFIGURATIONS Many applications require switched gains other than the ±1 and ±2 which the self-contained applications resistors provide. The AD630 can be readily programmed with three external resistors over a wide range of positive and negative gain by selecting and RB and RF to give the noninverting gain 1 + RF/RB and subsequent RA to give the desired inverting gain. Note that when the inverting magnitude equals the noninverting magnitude, the value of RA is found to be RBRF/(RB + RF). That is, RA should equal the parallel combination of RB and RF to match positive and negative gain. The feedback synthesis of the AD630 may also include reactive impedance. The gain magnitudes will match at all frequencies if the A impedance is made to equal the parallel combination of the B and F impedances. The same considerations apply to the AD630 as to conventional op amp feedback circuits. Virtually any function that can be realized with simple noninverting “L network” feedback can be used with the AD630. A common arrangement is shown in Figure 6. The low frequency gain of this circuit is 10. The response will have a pole (–3 dB) at a frequency f 1/(2 π 100 kΩC) and a zero (3 dB from the high frequency asymptote) at about 10 times this frequency. The 2 kΩ resistor in series with each capacitor mitigates the loading effect on circuitry driving this circuit, eliminates stability problems, and has a minor effect on the pole-zero locations. As a result of the reactive feedback, the high frequency components of the switched input signal will be transmitted at unity gain while the low frequency components will be amplified. This arrangement is useful in demodulators and lock-in amplifiers. It increases the circuit dynamic range when the modulation or interference is substantially larger than the desired signal amplitude. The output signal will contain the desired signal multiplied by the low frequency gain (which may be several hundred for large feedback ratios) with the switching signal and interference superimposed at unity gain. C –VS A B 10k VO 11.11k 12 Vi 100k 2k 2k C 2 20 19 18 13 7 8 9 10 SEL B SEL A CHANNEL STATUS B/A Figure 6. AD630 with External Feedback SWITCHED INPUT IMPEDANCE The noninverting mode of operation is a high input impedance configuration while the inverting mode is a low input impedance configuration. This means that the input impedance of the circuit undergoes an abrupt change as the gain is switched under control of the comparator. If gain is switched when the input signal is not zero, as it is in many practical cases, a transient will be delivered to the circuitry driving the AD630. In most applications, this will require the AD630 circuit to be driven by a low impedance source which remains “stiff ” at high frequencies. Generally, this will be a wideband buffer amplifier. FREQUENCY COMPENSATION The AD630 combines the convenience of internal frequency compensation with the flexibility of external compensation by means of an optional self-contained compensation capacitor. In gain of ±2 applications, the noise gain that must be addressed for stability purposes is actually 4. In this circumstance, the phase margin of the loop will be on the order of 60° without the optional compensation. This condition provides the maximum bandwidth and slew rate for closed loop gains of |2| and above. When the AD630 is used as a multiplexer, or in other configurations where one or both inputs are connected for unity gain feedback, the phase margin will be reduced to less than 20°. This may be acceptable in applications where fast slewing is a first priority, but the transient response will not be optimum. For these applications, the self-contained compensation capacitor may be added by connecting Pin 12 to Pin 13. This connection reduces the closed-loop bandwidth somewhat and improves the phase margin. For intermediate conditions, such as gain of ±1 where loop attenuation is 2, use of the compensation should be determined by whether bandwidth or settling response must be optimized. The optional compensation should also be used when the AD630 is driving capacitive loads or whenever conservative frequency compensation is desired. OFFSET VOLTAGE NULLING The offset voltages of both input stages and the comparator have been pretrimmed so that external trimming will only be required in the most demanding applications. The offset adjustment of the two input channels is accomplished by means of a differential and common-mode scheme. This facilitates fine adjustment of system errors in switched gain applications. With 元器件交易网www.cecb2b.com REV. E AD630 –8– the system input tied to 0 V, and a switching or carrier waveform applied to the comparator, a low level square wave will appear at the output. The differential offset adjustment potentiometers can be used to null the amplitude of this square wave (Pins 3 and 4). The common-mode offset adjustment can be used to zero the residual dc output voltage (Pins 5 and 6). These functions should be implemented using 10k trim potentiometers with wipers connected directly to Pin 8 as shown in Figures 9a and 9b. CHANNEL STATUS OUTPUT The channel status output, Pin 7, is an open collector output referenced to –VS that can be used to indicate which of the two input channels is active. The output will be active (pulled low) when Channel A is selected. This output can also be used to supply positive feedback around the comparator. This produces hysteresis which serves to increase noise immunity. Figure 7 shows an example of how hysteresis may be implemented. Note that the feedback signal is applied to the inverting (–) terminal of the comparator to achieve positive feedback. This is because the open collector channel status output inverts the output sense of the internal comparator. 1M 100k 100k –15V +5V 100 7 8 9 10 Figure 7. Comparator Hysteresis The channel status output may be interfaced with TTL inputs as shown in Figure 8. This circuit provides appropriate level shifting from the open-collector AD630 channel status output to TTL inputs. –15V +5V TTL INPUT AD630 +15V IN 914s 6.8k 22k 100k 2N2222 7 8 Figure 8. Channel Status—TTL Interface APPLICATIONS: BALANCED MODULATOR Perhaps the most commonly used configuration of the AD630 is the balanced modulator. The application resistors provide precise symmetric gains of ±1 and ±2. The ±1 arrangement is shown in Figure 9a and the ±2 arrangement is shown in Figure 9b. These cases differ only in the connection of the 10 kΩ feedback resistor (Pin 14) and the compensation capacitor (Pin 12). Note the use of the 2.5 kΩ bias current compensation resistors in these examples. These resistors perform the identical function in the ±1 gain case. Figure 10 demonstrates the performance of the AD630 when used to modulate a 100 kHz square wave carrier with a 10 kHz sinusoid. The result is the double sideband suppressed carrier waveform. These balanced modulator topologies accept two inputs, a signal (or modulation) input applied to the amplifying channels and a reference (or carrier) input applied to the comparator. MODULATED OUTPUT SIGNAL CARRIER INPUT CM ADJ DIFF ADJ 2.5k AMP A AMP B –V 10k 10k 5k 9 10 COMP 1 15 7 16 14 13 12 2 20 +VS –VS AD630 A 2.5k B 19 18 17 11 8 6 5 10k 4 3 10k MODULATION INPUT Figure 9a. AD630 Configured as a Gain-of-One Balanced Modulator MODULATED OUTPUT SIGNAL CARRIER INPUT CM ADJ DIFF ADJ 2.5k AMP A AMP B –V 10k 10k 5k 9 10 COMP 1 15 7 16 14 13 12 2 20 +VS –VS AD630 A 2.5k B 19 18 17 11 8 6 5 10k 4 3 10k MODULATION INPUT Figure 9b. AD630 Configured as a Gain-of-Two Balanced Modulator 10V 5V 5V 20s MODULATION INPUT CARRIER INPUT OUTPUT SIGNAL Figure 10. Gain-of-Two Balanced Modulator Sample Waveforms 元器件交易网www.cecb2b.com REV. E AD630 –9– BALANCED DEMODULATOR The balanced modulator topology described above will also act as a balanced demodulator if a double sideband suppressed carrier waveform is applied to the signal input and the carrier signal is applied to the reference input. The output under these circumstances will be the baseband modulation signal. Higher order carrier components that can be removed with a low-pass filter will also be present. Other names for this function are synchronous demodulation and phase-sensitive detection. PRECISION PHASE COMPARATOR The balanced modulator topologies of Figures 9a and 9b can also be used as precision phase comparators. In this case, an ac waveform of a particular frequency is applied to the signal input and a waveform of the same frequency is applied to the reference input. The dc level of the output (obtained by low-pass filtering) will be proportional to the signal amplitude and phase difference between the input signals. If the signal amplitude is held constant, the output can be used as a direct indication of the phase. When these input signals are 90° out of phase, they are said to be in quadrature and the AD630 dc output will be zero. PRECISION RECTIFIER ABSOLUTE VALUE If the input signal is used as its own reference in the balanced modulator topologies, the AD630 will act as a precision rectifier. The high frequency performance will be superior to that which can be achieved with diode feedback and op amps. There are no diode drops that the op amp must “leap over” with the commutating amplifier. LVDT SIGNAL CONDITIONER Many transducers function by modulating an ac carrier. A linear variable differential transformer (LVDT) is a transducer of this type. The amplitude of the output signal corresponds to core displacement. Figure 11 shows an accurate synchronous demodulation system which can be used to produce a dc voltage that corresponds to the LVDT core position. The inherent precision and temperature stability of the AD630 reduce demodulator drift to a second-order effect. A B 10k 10k 5k 2.5k 2.5k C 100k D 1F AD630 2 DEMODULATOR AD544 FOLLOWER B PHASE SHIFTER A E1000 SCHAEVITZ LVDT 2.5kHZ 2V p-p SINUSOIDAL EXCITATION 16 1 14 17 9 10 20 19 12 13 15 Figure 11. LVDT Signal Conditioner AC BRIDGE Bridge circuits that use dc excitation are often plagued by errors caused by thermocouple effects, 1/f noise, dc drifts in the electronics, and line noise pick-up. One way to get around these problems is to excite the bridge with an ac waveform, amplify the bridge output with an ac amplifier, and synchronously demodulate the resulting signal. The ac phase and amplitude information from the bridge is recovered as a dc signal at the output of the synchronous demodulator. The low frequency system noise, dc drifts, and demodulator noise all get mixed to the carrier frequency and can be removed by means of a low-pass filter. Dynamic response of the bridge must be traded off against the amount of attenuation required to adequately suppress these residual carrier components in the selection of the filter. Figure 12 is an example of an ac bridge system with the AD630 used as a synchronous demodulator. The bridge is excited by a 1 V 400 Hz excitation. Trace A in Figure 13 is the amplified bridge signal. Trace B is the output of the synchronous demodulator and Trace C is the filtered dc system output. AD8221 REF +IN –IN 49.9 350 350 350 350 CH B– SEL B CH A– SEL A RA RF RINA RINB –VS +15V VOUT +VS COMP AD630AR 12 13 1 8 RB 10 14 17 16 15 19 20 9 11 –15V 4.99k 4.99k 4.99k 2F 2F 2F A B C 1V 400Hz Figure 12. AC Bridge System 元器件交易网www.cecb2b.com REV. E AD630 –10– 500s/DIV B. 200mV/DIV C. 200mV/DIV 3 [ T ] T A. 200mV/DIV Figure 13. AC Bridge Waveforms (1 V Excitation) LOCK-IN AMPLIFIER APPLICATIONS Lock-in amplification is a technique used to separate a small, narrow-band signal from interfering noise. The lock-in amplifier acts as a detector and narrow-band filter combined. Very small signals can be detected in the presence of large amounts of uncorrelated noise when the frequency and phase of the desired signal are known. The lock-in amplifier is basically a synchronous demodulator followed by a low-pass filter. An important measure of performance in a lock-in amplifier is the dynamic range of its demodulator. The schematic diagram of a demonstration circuit which exhibits the dynamic range of an AD630 as it might be used in a lock-in amplifier is shown in Figure 14. Figure 15 is an oscilloscope photo demonstrating the large dynamic range of the AD630. The photo shows the recovery of a signal modulated at 400 Hz from a noise signal approximately 100,000 times larger. A B 10k 100R C OUTPUT LOW-PASS FILTER A B C R 100R AD630 10k 5k 2.5k 2.5k 20 19 17 1 16 AD542 13 AD542 14 10 9 CLIPPED BAND-LIMITED WHITE NOISE 100dB ATTENUATION 0.1Hz MODULATED 400Hz CARRIER CARRIER PHASE REFERENCE 15 Figure 14. Lock-In Amplifier 100 90 10 0% 5V 5V 5s 5mV MODULATED SIGNAL (A) (UNATTENUATED) ATTENUATED SIGNAL PLUS NOISE (B) OUTPUT Figure 15. Lock-In Amplifier Waveforms The test signal is produced by modulating a 400 Hz carrier with a 0.1 Hz sine wave. The signals produced, for example, by chopped radiation (i.e., IR, optical) detectors may have similar low frequency components. A sinusoidal modulation is used for clarity of illustration. This signal is produced by a circuit similar to Figure 9b and is shown in the upper trace of Figure 15. It is attenuated 100,000 times normalized to the output, B, of the summing amplifier. A noise signal that might represent, for example, background and detector noise in the chopped radiation case, is added to the modulated signal by the summing amplifier. This signal is simply band limited clipped white noise. Figure 15 shows the sum of attenuated signal plus noise in the center trace. This combined signal is demodulated synchronously using phase information derived from the modulator, and the result is low-pass filtered using a 2-pole simple filter which also provides a gain of 100 to the output. This recovered signal is the lower trace of Figure 15. The combined modulated signal and interfering noise used for this illustration is similar to the signals often requiring a lock-in amplifier for detection. The precision input performance of the AD630 provides more than 100 dB of signal range and its dynamic response permits it to be used with carrier frequencies more than two orders of magnitude higher than in this example. A more sophisticated low-pass output filter will aid in rejecting wider bandwidth interference. 元器件交易网www.cecb2b.com REV. E AD630 –11– OUTLINE DIMENSIONS 20-Lead Side-Brazed Ceramic Dual In-Line Package [SBDIP] (D-20) Dimensions shown in inches and (millimeters) 20 1 10 11 0.300 (7.62) PIN 1 0.280 (7.11) 0.005 (0.13) MIN 0.080 (2.03) MAX SEATING PLANE 0.023 (0.58) 0.014 (0.36) 0.060 (1.52) 0.015 (0.38) 0.200 (5.08) MAX 0.200 (5.08) 0.125 (3.18) 0.070 (1.78) 0.030 (0.76) 0.100 (2.54) BSC 0.150 (3.81) MIN 0.320 (8.13) 0.300 (7.62) 0.015 (0.38) 0.008 (0.20) CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 1.060 (28.92) 0.990 (25.15) 20-Lead Plastic Dual In-Line Package [PDIP] (N-20) Dimensions shown in inches and (millimeters) 20 1 10 11 0.985 (25.02) 0.965 (24.51) 0.945 (24.00) 0.295 (7.49) 0.285 (7.24) 0.275 (6.99) 0.150 (3.81) 0.135 (3.43) 0.120 (3.05) 0.015 (0.38) 0.010 (0.25) 0.008 (0.20) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) SEATING PLANE 0.015 (0.38) MIN 0.180 (4.57) MAX 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.150 (3.81) 0.130 (3.30) 0.110 (2.79) 0.100 (2.54) BSC 0.060 (1.52) 0.050 (1.27) 0.045 (1.14) CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COMPLIANT TO JEDEC STANDARDS MO-095-AE 20-Terminal Ceramic Leadless Chip Carrier [LCC] (E-20A) Dimensions shown in inches and (millimeters) 1 20 4 9 8 13 19 14 3 18 BOTTOM VIEW 0.028 (0.71) 0.022 (0.56) 45 TYP 0.015 (0.38) MIN 0.055 (1.40) 0.045 (1.14) 0.050 (1.27) BSC 0.075 (1.91) REF 0.011 (0.28) 0.007 (0.18) R TYP 0.095 (2.41) 0.075 (1.90) 0.100 (2.54) REF 0.200 (5.08) REF 0.150 (3.81) BSC 0.075 (1.91) REF 0.358 (9.09) 0.342 (8.69) SQ 0.358 (9.09) MAX SQ 0.100 (2.54) 0.064 (1.63) 0.088 (2.24) 0.054 (1.37) CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETERS DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 元器件交易网www.cecb2b.com –12– REV. E C00784–0–6/04(E) Revision History Location Page 6/04—Data Sheet changed from REV. D to REV. E. Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Replaced Figure 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Changes to AC BRIDGE section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Replaced Figure 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Changes to LOCK-IN AMPLIFIER APPLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 6/01—Data Sheet changed from REV. C to REV. D. Changes to SPECIFICATION TABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Changes to THERMAL CHARACTERISTICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Changes to PIN CONFIGURATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Changes to OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 20-Lead Standard Small Outline Package [SOIC] Wide Body (R-20) Dimensions shown in millimeters and (inches) CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN COMPLIANT TO JEDEC STANDARDS MS-013AC 0.75 (0.0295) 0.25 (0.0098) 20 11 1 10 8 0 45 1.27 (0.0500) 0.40 (0.0157) SEATING PLANE 0.30 (0.0118) 0.10 (0.0039) 2.65 (0.1043) 2.35 (0.0925) 1.27 (0.0500) BSC 10.65 (0.4193) 10.00 (0.3937) 7.60 (0.2992) 7.40 (0.2913) 13.00 (0.5118) 12.60 (0.4961) COPLANARITY 0.10 0.33 (0.0130) 0.20 (0.0079) 0.51 (0.0201) 0.31 (0.0122) AD630 元器件交易网www.cecb2b.com

AD630.pdf

AD630仿真模型，Multisim 10以上可用 AD630仿真模型，Multisim 10以上可用

基于AD630设计的锁定放大器，包含仿真文件和报告，可以参考，包含移相电路、比较器、滤波电路、乘法器等结构

本例中的电路采用AnalogDevices公司的AD630平衡调制解调IC实现了一种简单的低成本锁入放大器。该器件使用激光微调薄膜电阻，这带来了很高的准确性和稳定性，并因此产生了一种灵活的换向体系结构。它可用于同步检测等先进的信号处理应用。如果知道信号的频率与相位，那么即使存在振幅大得多的噪声源，该放大器也能检测出微弱的AC信号。

AD630中文手册及使用案例.pdf

针对目前蓄电池内阻在线测量存在的不足，设计实现了一套实用的蓄电池内阻在线测量系统。该系统运用四引线连接法，将一定频率的交流信号注入电池，再将电池两端产生的微弱信号通过前置放大滤波，送入AD630 进行相关检测，有效地抑制了噪声和干扰，简化了设计，实现了蓄电池内阻的在线测量。实验结果表明，该系统可有效地应用于蓄电池内阻的在线测量，且测量结果稳定可靠。

利用交流注入法实现蓄电池内阻的在线测量，利用锁相放大器AD630处理小信号电路，提高了测量精度，测量误差小于10%；通过RS485实现数据交换，便于集成于其他系统，满足用户多方面的需求；并设计了电源回路，测量系统的电源可由被测量电池提供，也可由外部电源提供。

AD630 AD设计 Altium设计 硬件原理图+PCB文件,2层板设计，Altium Designer 设计的工程文件，包括完整的原理图及PCB文件，可以用Altium(AD)软件打开或修改，可作为你产品设计的参考。