android读写文件例程，在data/data/example.fliedemo/下生成一个abcd.txt文件。

Redis集群-Redis安装、Redis主从复制、哨兵、Redis集群

新视野大学英语读写教程4原文及答案 新视野大学英语读写教程4原文及答案

新视野大学英语读写第四册课后习题答案及讲解

运行选择完全格式化，就可以把U盘初始化，跟出厂设置相似。

使用verilog语言，通过FPGA控制AT24C02C EEPROM，硬件上需要注意，根据硬件连接芯片的A2 A1 A0 电平，编写Device Address字节内容，本设计使用的是A2=0,A1=0,A0=1; 由两个小模块和一个顶层模块组成： iic.v 是iic通讯子模块，可以实现特定地址的读写功能。一次读写一个字节。 iic_ctrl.v 是上层的应用子模块，主要是使用vio控制8个字节接口，使能后配置写入到编辑好的8个地址中。(地址可以在模块里修改 范围为0xx0~0xFF,共256byte)上电时rst_置1后，从eeprom中读取这8个字节的数据。用于配置一些其他功能模块之类。可以根据使用情景自行修改。可以自己加ila看一下相关的时序控制。 TOP.v是顶层模块，外接线路只有rst复位，sys_clk系统时钟，I2C_SDA 数据线iic的，I2C_SCL 时钟线iic的。自己生成工程的时候记得添加vio作为控制输入看一下。 祝开发顺利~稍后会简单整理一下开发心得，调试过程中的注意事项。

ACR122U工具合集包 M1/UID/CUID/FUID/UFUID/RFID读写格式化 含CUID卡写错导致无法写入SAK修复  非全加密密钥解码 全加密密钥解码 命令读写功能

注册表操作类V1.1 可支持X86与X64读写的注册表模块源码 得力科技

To write the new Voltage Divider value can be programmed as follows: - SubclassID for “Voltage Divider” is 104 or 0x68 hex, and offset is 14 - Write 0x00 using BlockDataControl() command (0x61) to enable block data flash control. (wr 0x61 0x00) - Write 0x68 (Calibration Subclass) using the DataFlashClass() command (0x3E) to access the Registers subclass. (wr 0x3E 0x68) - Write the block offset location using DataFlashBlock() command (0x3F). To access data located at offset 0 to 31, use offset = 0x00. For example, Voltage Divider (offset = 14) is in the first block so use (wr 0x3F 0x00). - To read the data of a specific offset, use address 0x40 + mod(offset, 32). So to read the old Voltage divider (rd 0x4E old_Voltage Divider_MSB) (rd 0x4F old_Voltage Divider_LSB) - To write the data of a specific offset, use address 0x40 + mod(offset, 32). So to write the new Voltage divider (rd 0x4E new_Voltage Divider_MSB) (rd 0x4F new_Voltage Divider_LSB) - The data is actually transferred to the data flash when the correct checksum for the whole block (0x40 to 0x5F) is written to BlockDataChecksum() (0x60). (wr 0x60 NEW_checksum) The checksum is (255-x) where x is the 8-bit summation of the BlockData() (0x40 to 0x5F) on a byte-by-byte basis. A quick way to calculate the new checksum is to make use of the old checksum: (a) temp = mod (255 – OLD_checksum – old_Voltage Divider_MSB - old_Voltage Divider_LSB), 256)(b) NEW_checksum = 255 – mod (temp + new_Voltage Divider_MSB + new_Voltage Divider_LSB, 256) Step 3. Update any individual flash locations, such as serial number, lot code, and date: In a similar manner to the Voltage divider, any pack specific data such as serial number, lot code and date can be changed during the production process.

美萍写狗程序--很多人都需要的哦可以直接写狗，里面有单机版和网络版的数据