d卡实验Verilog逻辑源码Quartus工程文件+文档说明,FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 module sd_card_test( input clk, input rst_n, input key1, output SD_nCS, output SD_DCLK, output SD_MOSI, input SD_MISO, output [5:0] seg_sel, output [7:0] seg_data ); parameter S_IDLE = 0; parameter S_READ = 1; parameter S_WRITE = 2; parameter S_END = 3; reg[3:0] state; wire sd_init_done; reg sd_sec_read; wire[31:0] sd_sec_read_addr; wire[7:0] sd_sec_read_data; wire sd_sec_read_data_valid; wire sd_sec_read_end; reg sd_sec_write; wire[31:0] sd_sec_write_addr; reg [7:0] sd_sec_write_data; wire sd_sec_write_data_req; wire sd_sec_write_end; reg[9:0] wr_cnt; reg[9:0] rd_cnt; wire button_negedge; reg[7:0] read_data; ax_debounce ax_debounce_m0 ( .clk (clk), .rst (~rst_n), .button_in (key1), .button_posedge (), .button_negedge (button_negedge), .button_out () ); wire[6:0] seg_data_0; seg_decoder seg_decoder_m0( .bin_data (read_data[3:0]), .seg_data (seg_data_0) ); wire[6:0] seg_data_1; seg_decoder seg_decoder_m1( .bin_data (read_data[7:4]), .seg_data (seg_data_1) ); seg_scan seg_scan_m0( .clk (clk), .rst_n (rst_n), .seg_sel (seg_sel), .seg_data (seg_data), .seg_data_0 ({1'b1,7'b1111_111}), .seg_data_1 ({1'b1,7'b1111_111}), .seg_data_2 ({1'b1,7'b1111_111}), .seg_data_3 ({1'b1,7'b1111_111}), .seg_data_4 ({1'b1,seg_data_1}), .seg_data_5 ({sd_init_done,seg_data_0}) ); always@(posedge clk or negedge rst_n) begin if(rst_n == 1'b0) wr_cnt <= 10'd0; else if(state == S_WRITE) begin if(sd_sec_write_data_req == 1'b1) wr_cnt <= wr_cnt + 10'

基于FPGA设计的vga显示测试实验Verilog逻辑源码Quartus工程文件+文档说明，FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 module top( input clk, input rst_n, //vga output output vga_out_hs, //vga horizontal synchronization output vga_out_vs, //vga vertical synchronization output[4:0] vga_out_r, //vga red output[5:0] vga_out_g, //vga green output[4:0] vga_out_b //vga blue ); wire video_clk; wire video_hs; wire video_vs; wire video_de; wire[7:0] video_r; wire[7:0] video_g; wire[7:0] video_b; assign vga_out_hs = video_hs; assign vga_out_vs = video_vs; assign vga_out_r = video_r[7:3]; //discard low bit data assign vga_out_g = video_g[7:2]; //discard low bit data assign vga_out_b = video_b[7:3]; //discard low bit data //generate video pixel clock video_pll video_pll_m0( .inclk0(clk), .c0(video_clk)); color_bar color_bar_m0( .clk(video_clk), .rst(~rst_n), .hs(video_hs), .vs(video_vs), .de(video_de), .rgb_r(video_r), .rgb_g(video_g), .rgb_b(video_b) ); endmodule

基于FPGA设计的sdram读写测试实验Verilog逻辑源码Quartus工程文件+文档说明，DRAM选用海力士公司的 HY57V2562 型号,容量为的 256Mbit,采用了 54 引脚的 TSOP 封装, 数据宽度都为 16 位, 工作电压为 3.3V,并丏采用同步接口方式所有的信号都是时钟信号。FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 timescale 1ps/1ps module top ( input clk, input rst_n, output[1:0] led, output sdram_clk, //sdram clock output sdram_cke, //sdram clock enable output sdram_cs_n, //sdram chip select output sdram_we_n, //sdram write enable output sdram_cas_n, //sdram column address strobe output sdram_ras_n, //sdram row address strobe output[1:0] sdram_dqm, //sdram data enable output[1:0] sdram_ba, //sdram bank address output[12:0] sdram_addr, //sdram address inout[15:0] sdram_dq //sdram data ); parameter MEM_DATA_BITS = 16 ; //external memory user interface data width parameter ADDR_BITS = 24 ; //external memory user interface address width parameter BUSRT_BITS = 10 ; //external memory user interface burst width parameter BURST_SIZE = 128 ; //burst size wire wr_burst_data_req; // from external memory controller,write data request ,before data 1 clock wire wr_burst_finish; // from external memory controller,burst write finish wire rd_burst_finish; // from external memory controller,burst read finish wire rd_burst_req; // to external memory controller,send out a burst read request wire wr_burst_req; // to external memory controller,send out a burst write request wire[BUSRT_BITS - 1:0] rd_burst_len; // to e

基于FGGA设计的音频录音与播放实验例程Verilog逻辑源码Quartus工程文件+文档说明,音频编解码芯片选用WOLFSON 公司的 WM8731 芯，FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 `timescale 1ps/1ps module top ( input clk, //clock input input rst_n, //reset input input key, //record play button input wm8731_bclk, //audio bit clock input wm8731_daclrc, //DAC sample rate left right clock output wm8731_dacdat, //DAC audio data output input wm8731_adclrc, //ADC sample rate left right clock input wm8731_adcdat, //ADC audio data input inout wm8731_scl, //I2C clock inout wm8731_sda, //I2C data output sdram_clk, //sdram clock output sdram_cke, //sdram clock enable output sdram_cs_n, //sdram chip select output sdram_we_n, //sdram write enable output sdram_cas_n, //sdram column address strobe output sdram_ras_n, //sdram row address strobe output[1:0] sdram_dqm, //sdram data enable output[1:0] sdram_ba, //sdram bank address output[12:0] sdram_addr, //sdram address inout[15:0] sdram_dq //sdram data ); parameter MEM_DATA_BITS = 16 ; //external memory user interface data width parameter ADDR_BITS = 24 ; //external memory user interface address width parameter BUSRT_BITS = 10 ; //external memory user interface burst width wire wr_burst_data_req; wire

基于FPGA设计的SD卡音乐播放Verilog逻辑源码Quartus工程文件+文档说明，音频编解码芯片选用WOLFSON 公司的 WM8731 芯，FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 module top( input clk, input rst_n, input key1, input wm8731_bclk, //audio bit clock input wm8731_daclrc, //DAC sample rate left right clock output wm8731_dacdat, //DAC audio data output input wm8731_adclrc, //ADC sample rate left right clock input wm8731_adcdat, //ADC audio data input inout wm8731_scl, //I2C clock inout wm8731_sda, //I2C data output sd_ncs, //SD card chip select (SPI mode) output sd_dclk, //SD card clock output sd_mosi, //SD card controller data output input sd_miso, //SD card controller data input output [5:0] seg_sel, output [7:0] seg_data ); wire[9:0] lut_index; wire[31:0] lut_data; wire[3:0] state_code; wire[6:0] seg_data_0; //I2C master controller i2c_config i2c_config_m0( .rst (~rst_n ), .clk (clk ), .clk_div_cnt (16'd99 ), .i2c_addr_2byte (1'b0 ), .lut_index (lut_index ), .lut_dev_addr (lut_data[31:24] ), .lut_reg_addr (lut_data[23:8] ), .lut_reg_data (lut_data[7:0] ), .error ( ), .done ( ), .i2c_scl

基于FPGA设计的字符VGA LCD显示实验Verilog逻辑源码Quartus工程文件+文档说明,通过字符转换工具将字符转换为 8 进制 mif 文件存放到单端口的 ROM IP 核中，再从 ROM 中把转换后的数据读取出来显示到 VGA 上，FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 module top( input clk, input rst_n, //vga output output vga_out_hs, //vga horizontal synchronization output vga_out_vs, //vga vertical synchronization output[4:0] vga_out_r, //vga red output[5:0] vga_out_g, //vga green output[4:0] vga_out_b //vga blue ); wire video_clk; wire video_hs; wire video_vs; wire video_de; wire[7:0] video_r; wire[7:0] video_g; wire[7:0] video_b; wire osd_hs; wire osd_vs; wire osd_de; wire[7:0] osd_r; wire[7:0] osd_g; wire[7:0] osd_b; assign vga_out_hs = osd_hs; assign vga_out_vs = osd_vs; assign vga_out_r = osd_r[7:3]; //discard low bit data assign vga_out_g = osd_g[7:2]; //discard low bit data assign vga_out_b = osd_b[7:3]; //discard low bit data //generate video pixel clock video_pll video_pll_m0( .inclk0 (clk ), .c0 (video_clk ) ); color_bar color_bar_m0( .clk (video_clk ), .rst (~rst_n ), .hs (video_hs ), .vs (video_vs ), .de (video_de ), .rgb_r (video_r ), .rgb_g (video_g ), .rgb_b

读取SD卡中的BMP图片并通过VGA LCD屏显示的Verilog逻辑源码Quartus工程文件+文档说明，实验将SD卡里的BMP图片读出，写入到外部存储器，再通过 VGA、LCD 等显示，FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 module top( input clk, input rst_n, input key1, output [5:0] seg_sel, output [7:0] seg_data, output vga_out_hs, //vga horizontal synchronization output vga_out_vs, //vga vertical synchronization output[4:0] vga_out_r, //vga red output[5:0] vga_out_g, //vga green output[4:0] vga_out_b, //vga blue output sd_ncs, //SD card chip select (SPI mode) output sd_dclk, //SD card clock output sd_mosi, //SD card controller data output input sd_miso, //SD card controller data input output sdram_clk, //sdram clock output sdram_cke, //sdram clock enable output sdram_cs_n, //sdram chip select output sdram_we_n, //sdram write enable output sdram_cas_n, //sdram column address strobe output sdram_ras_n, //sdram row address strobe output[1:0] sdram_dqm, //sdram data enable output[1:0] sdram_ba, //sdram bank address output[12:0] sdram_addr, //sdram address inout[15:0] sdram_dq //sdram data ); parameter MEM_DATA_BITS = 16 ; //external memory user interface data width parameter ADDR_BITS = 24 ; //external memory user interface address width parameter BUSRT_BITS = 10 ; //external memory user interface burst width wire

FPGA读取OV5640摄像头数据并通过VGA或LCD屏显示输出的Verilog逻辑源码Quartus工程文件+文档说明，FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 module top( input clk, input rst_n, output cmos_scl, //cmos i2c clock inout cmos_sda, //cmos i2c data input cmos_vsync, //cmos vsync input cmos_href, //cmos hsync refrence,data valid input cmos_pclk, //cmos pxiel clock output cmos_xclk, //cmos externl clock input [7:0] cmos_db, //cmos data output cmos_rst_n, //cmos reset output cmos_pwdn, //cmos power down output vga_out_hs, //vga horizontal synchronization output vga_out_vs, //vga vertical synchronization output[4:0] vga_out_r, //vga red output[5:0] vga_out_g, //vga green output[4:0] vga_out_b, //vga blue output sdram_clk, //sdram clock output sdram_cke, //sdram clock enable output sdram_cs_n, //sdram chip select output sdram_we_n, //sdram write enable output sdram_cas_n, //sdram column address strobe output sdram_ras_n, //sdram row address strobe output[1:0] sdram_dqm, //sdram data enable output[1:0] sdram_ba, //sdram bank address output[12:0] sdram_addr, //sdram address inout[15:0] sdram_dq //sdram data ); parameter MEM_DATA_BITS = 16; //external memory user interface data width parameter ADDR_BITS = 24; //external memory user interface address width p

FPGA读取AD芯片AD9238数据并波形显示例程Verilog逻辑源码Quartus工程文件+文档说明，FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 module top( input clk, input rst_n, output ad9238_clk_ch0, output ad9238_clk_ch1, input[11:0] ad9238_data_ch0, input[11:0] ad9238_data_ch1, //vga output output vga_out_hs, //vga horizontal synchronization output vga_out_vs, //vga vertical synchronization output[4:0] vga_out_r, //vga red output[5:0] vga_out_g, //vga green output[4:0] vga_out_b //vga blue ); wire video_clk; wire video_hs; wire video_vs; wire video_de; wire[7:0] video_r; wire[7:0] video_g; wire[7:0] video_b; wire grid_hs; wire grid_vs; wire grid_de; wire[7:0] grid_r; wire[7:0] grid_g; wire[7:0] grid_b; wire wave0_hs; wire wave0_vs; wire wave0_de; wire[7:0] wave0_r; wire[7:0] wave0_g; wire[7:0] wave0_b; wire wave1_hs; wire wave1_vs; wire wave1_de; wire[7:0] wave1_r; wire[7:0] wave1_g; wire[7:0] wave1_b; wire adc_clk; wire adc0_buf_wr; wire[10:0] adc0_buf_addr; wire[7:0] adc0_buf_data; wire adc1_buf_wr; wir

FPGA读取模数转换芯片AD7606数据并波形显示例程Verilog逻辑源码Quartus工程文件+文档说明，FPGA型号Cyclone4E系列中的EP4CE6F17C8，Quartus版本17.1。 module top( input clk, input rst_n, input[15:0] ad7606_data, //ad7606 data input ad7606_busy, //ad7606 busy input ad7606_first_data, //ad7606 first data output[2:0] ad7606_os, //ad7606 output ad7606_cs, //ad7606 AD cs output ad7606_rd, //ad7606 AD data read output ad7606_reset, //ad7606 AD reset output ad7606_convstab, //ad7606 AD convert start //vga output output vga_out_hs, //vga horizontal synchronization output vga_out_vs, //vga vertical synchronization output[4:0] vga_out_r, //vga red output[5:0] vga_out_g, //vga green output[4:0] vga_out_b //vga blue ); wire video_clk; wire video_hs; wire video_vs; wire video_de; wire[7:0] video_r; wire[7:0] video_g; wire[7:0] video_b; wire grid_hs; wire grid_vs; wire grid_de; wire[7:0] grid_r; wire[7:0] grid_g; wire[7:0] grid_b; wire wave0_hs; wire wave0_vs; wire wave0_de; wire[7:0] wave0_r; wire[7:0] wave0_g; wire[7:0] wave0_b; wire wave1_hs; wire wave1_vs; wire