16路PWM舵机模块驱动程序51单片机

驱动程序

淘宝上卖的16路PWM舵机驱动模块的51单片机程序部分程序如下 #include #include #include #include typedef unsigned char uchar; typedef unsigned int uint; sbit scl=P1^3; //时钟输入线 sbit sda=P1^4; //数据输入/输出端 sbit KEY1=P2^0; sbit KEY2=P2^1; #define PCA9685_adrr 0x80// 1+A5+A4+A3+A2+A1+A0+w/r //片选地址，将焊接点置1可改变地址， // 当IIC总呱嫌多片PCA9685或相同地址时才需焊接 // #define PCA9685_SUBADR1 0x2 // #define PCA9685_SUBADR2 0x3 // #define PCA9685_SUBADR3 0x4 #define PCA9685_MODE1 0x0 #define PCA9685_PRESCALE 0xFE #define LED0_ON_L 0x6 #define LED0_ON_H 0x7 #define LED0_OFF_L 0x8 #define LED0_OFF_H 0x9 // #define ALLLED_ON_L 0xFA // #define ALLLED_ON_H 0xFB // #define ALLLED_OFF_L 0xFC // #define ALLLED_OFF_H 0xFD #define SERVOMIN 115 // this is the 'minimum' pulse length count (out of 4096) #define SERVOMAX 590 // this is the 'maximum' pulse length count (out of 4096) #define SERVO000 130 //0度对应4096的脉宽计数值 #define SERVO180 520 //180度对应4096的脉宽计算值，四个值可根据不同舵机修改 /**********************函数的声明*********************************/ /*--------------------------------------------------------------- 毫秒延时函数 ----------------------------------------------------------------*/ void delayms(uint z) { uint x,y; for(x=z;x>0;x--) for(y=148;y>0;y--); } /*--------------------------------------------------------------- IIC总线所需的通用函数 ----------------------------------------------------------------*/ /*--------------------------------------------------------------- 微妙级别延时函数大于4.7us ----------------------------------------------------------------*/ void delayus() { _nop_(); //在intrins.h文件里 _nop_(); _nop_(); _nop_(); _nop_(); } /*--------------------------------------------------------------- IIC总线初始化函数 ----------------------------------------------------------------*/ void init() { sda=1; //sda scl使用前总是被拉高 delayus(); scl=1; delayus(); } /*--------------------------------------------------------------- IIC总线启动信号函数 ----------------------------------------------------------------*/ void start() { sda=1; delayus(); scl=1; //scl拉高时 sda突然来个低电平就启动了IIC总线 delayus(); sda=0; delayus(); scl=0; delayus(); } /*--------------------------------------------------------------- IIC总线停止信号函数 ----------------------------------------------------------------*/ void stop() { sda=0; delayus(); scl=1; //scl拉高时 sda突然来个高电平就停止了IIC总线 delayus(); sda=1; delayus(); } /*--------------------------------------------------------------- IIC总线应答信号函数 ----------------------------------------------------------------*/ void ACK() { uchar i; scl=1; delayus(); while((sda=1)&&(i<255)) i++; scl=0; delayus(); } /*--------------------------------------------------------------- 写一个字节,无返回值，需输入一个字节值 ----------------------------------------------------------------*/ void write_byte(uchar byte) { uchar i,temp; temp=byte; for(i=0;i<8;i++) { temp=temp<<1; scl=0; delayus(); sda=CY; delayus(); scl=1; delayus(); } scl=0; delayus(); sda=1; delayus(); } /*--------------------------------------------------------------- 读一个字节函数，有返回值 ----------------------------------------------------------------*/ uchar read_byte() { uchar i,j,k; scl=0; delayus(); sda=1; delayus(); for(i=0;i<8;i++) { delayus(); scl=1; delayus(); if(sda==1) { j=1; } else j=0; k=(k<< 1)|j; scl=0; } delayus(); return k; } /*--------------------------------------------------------------- 有关PCA9685模块的函数 ----------------------------------------------------------------*/ /*--------------------------------------------------------------- 向PCA9685里写地址，数据 ----------------------------------------------------------------*/ void PCA9685_write(uchar address,uchar date) { start(); write_byte(PCA9685_adrr); //PCA9685的片选地址 ACK(); write_byte(address); //写地址控制字节 ACK(); write_byte(date); //写数据 ACK(); stop(); } /*--------------------------------------------------------------- 从PCA9685里的地址值中读数据(有返回值) ----------------------------------------------------------------*/ uchar PCA9685_read(uchar address) { uchar date; start(); write_byte(PCA9685_adrr); //PCA9685的片选地址 ACK(); write_byte(address); ACK(); start(); write_byte(PCA9685_adrr|0x01); //地址的第八位控制数据流方向，就是写或读 ACK(); date=read_byte(); stop(); return date; }

文件下载

资源详情

[{"title":"（ 18 个子文件 50KB ） 16路PWM舵机模块驱动程序51单片机","children":[{"title":"舵机模块222","children":[{"title":"project","children":[{"title":"1.uvproj 13.25KB ","children":null,"spread":false},{"title":"1_uvproj.bak 0B ","children":null,"spread":false},{"title":"1.uvgui.Zjm 67.57KB ","children":null,"spread":false},{"title":"1.plg 6.96KB ","children":null,"spread":false},{"title":"1_uvopt.bak 5.74KB ","children":null,"spread":false},{"title":"1.uvgui_Zjm.bak 67.57KB ","children":null,"spread":false},{"title":"STARTUP.A51 6.23KB ","children":null,"spread":false},{"title":"1.uvopt 5.75KB ","children":null,"spread":false}],"spread":true},{"title":"output","children":[{"title":"main.lst 16.57KB ","children":null,"spread":false},{"title":"1.m51 18.32KB ","children":null,"spread":false},{"title":"1 15.11KB ","children":null,"spread":false},{"title":"1.plg 192B ","children":null,"spread":false},{"title":"main.obj 14.83KB ","children":null,"spread":false},{"title":"STARTUP.obj 818B ","children":null,"spread":false},{"title":"1.lnp 108B ","children":null,"spread":false},{"title":"STARTUP.lst 13.82KB ","children":null,"spread":false},{"title":"1.hex 5.35KB ","children":null,"spread":false}],"spread":true},{"title":"src","children":[{"title":"main.c 10.52KB ","children":null,"spread":false}],"spread":true}],"spread":true}],"spread":true}]

评论信息

其他资源

免责申明

【只为小站】的资源来自网友分享，仅供学习研究，请务必在下载后24小时内给予删除，不得用于其他任何用途，否则后果自负。基于互联网的特殊性，【只为小站】无法对用户传输的作品、信息、内容的权属或合法性、合规性、真实性、科学性、完整权、有效性等进行实质审查；无论【只为小站】经营者是否已进行审查，用户均应自行承担因其传输的作品、信息、内容而可能或已经产生的侵权或权属纠纷等法律责任。
本站所有资源不代表本站的观点或立场，基于网友分享，根据中国法律《信息网络传播权保护条例》第二十二条之规定，若资源存在侵权或相关问题请联系本站客服人员，zhiweidada#qq.com，请把#换成@，本站将给予最大的支持与配合，做到及时反馈和处理。关于更多版权及免责申明参见版权及免责申明

16路PWM舵机模块驱动程序51单片机

文件下载

资源详情

评论信息

其他资源

免责申明

个人信息

相关资源标签

热门下载

最新下载