PVS-Studio 6.00官方版 附带注册码： Name:pvs SerialNumber:B1TG-6CYJ-0A07-YX01 LicenseType:Site License LicenseValidThru:2099/12/31

用于LPC2000系列芯片的程序烧录 /*Hints on Using the LPC2000 Flash Utility This document can be considered as a supplement to the already existing Application note AN10302 “Using the Philips LPC2000 Flash Utility”, which is provided in the same zip file. The Application note covers the following topics: 1. LPC2000 ISP Overview 2. ISP Mode Entry- Manual and RTS/DTR control circuit 3. Flash and RAM buffer operations 4. Keil MCB2100 board and IAR/Philips 210x KickStart board. Topics discussed in this guide are as follows: 1. Using the “Compare Flash” ISP command. 2. Flashless devices- LPC2220, LPC2210, LPC2290 Using the Compare Flash: The below steps need not be carried out if the checksum is part of the code before it is compiled. This would mean that checksum would be part of the hex file been created. For more detailed information on the checksum calculation please refer to the “Flash Memory System and Programming” chapter in the respective device User Manual. In this case, the hex file can be directly loaded using the “Upload to Flash” button and then the “ Compare Flash” button can be used to compare the Flash contents with the hex file. This direct operation is possible since the signature (or checksum) is part of the hex file already. The below steps need to be carried out if the checksum calculation is not part of the code been compiled. In this case, the checksum calculation has to be done by the utility. Step1: Open the “Buffer” menu and browse to “Flash Buffer operations”. When this menu item is clicked the following window will pop-up. Step2: Now click on the “Load Hex file” button. Please browse to the hex file, which needs to be downloaded into Flash. In this case, Blinky.hex would be loaded. Step3: Select the hex file and press “Open”. This would load the hex file into the buffer window as shown below. Please take a note of location 0x14. In this case, the checksum is not computed before the code is compiled. Step4: Now click on the “Vector Calc” button, which would calculate the checksum and load it at the reserved memory location, 0x14. As shown below this location gets updated. The updated value at 0x14 is as shown below Step5: Since this hex file is modified with the checksum, it needs to be saved back into the same location from where it was loaded. Clicking on the “Save Hex File” button would complete this step. When this is done, a message as shown below should appear. Click “Yes”. Step6: Download the hex file into Flash by clicking on the “Download Flash” button. The progress window should show the progress of the Flash download. Step7: The Flash Buffer Operations window can now be closed. Now, please click here and browse to “Blinky.hex” again. Now click the “Compare Flash” button and it should be a success. Flashless devices- LPC2220, LP2210, LPC2290: Since the LPC2220/2210/2290 does not have on-chip Flash, the ISP utility does not have these devices in its listing of supported Flash devices. However, the utility can still be used to issue ISP commands that would access the on-chip SRAM (using RAM Buffer Operations Window) and bootloader specific ISP commands like Read Device ID. For instance, when the above button is clicked, the ISP utility would complain saying that the “Type is not supported” which basically means that this device is not present in the listing of Flash devices. This error message can be ignored. After “OK” is pressed in the above message, the ISP commands will still be executed and the Part ID and the Boot loader ID will be displayed.*/ /*AN10302 Using the Philips LPC2000 Flash utility with the Keil MCB2100 and IAR LPC210x Kickstart evaluation boards Rev. 03 — 10 June 2004 Application note Document information Info Content Keywords LPC2000, Flash utility, Keil MCB2100, IAR LPC210x Abstract Application information for the Philips LPC2000 Flash utility with the Keil MCB2100 and IAR LPC210x Kickstart evaluation boards 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 2 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility Contact information For additional information, please visit: http://www.semiconductors.philips.com For sales office addresses, please send an email to: sales.addresses@www.semiconductors.philips.com Revision history Rev Date Description 3 10 June 2004 Third version (9397 750 13354). Modifications: • Updated Table 2. • Updated Section 4.2.1. 2 12 May 2004 Second version (9397 750 13287). 1 30 April 2004 Initial version (9397 750 13231). 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 3 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility 1. Introduction In-System programming (ISP) is a method of programming and erasing the on-chip flash or RAM memory using the boot loader software and a serial port. The part may reside in the end-user system. The flash boot loader provides an In-System Programming interface for programming the on-chip flash or RAM memory. This boot loader is located in the upper 8 kB of flash memory, it can be read but not written to or erased. 2. LPC2000 ISP overview The flash boot loader code is executed every time the part is powered on or reset. The loader can execute the ISP command handler or pass execution to the user application code. A LOW level, after reset, at the P0.14 pin is considered as the external hardware request to start the ISP command handler. The boot loader samples this pin during reset. Assuming that proper signal is present on X1 pin when the rising edge on RST pin is generated, it may take up to 3 ms before P0.14 is sampled and the decision on whether to continue with user code or ISP handler is made. If P0.14 is sampled LOW and the watchdog overflow flag is set, the external hardware request to start the ISP command handler is ignored. If there is no request for the ISP command handler execution (P0.14 is sampled HIGH after reset), a search is made for a valid user program. If a valid user program is found then the execution control is transferred to it. If a valid user program is not found, the auto-baud routine is invoked. Pin P0.14 is used as hardware request for ISP requires special attention. Since P0.14 is in high impedance mode after reset, it is important that the user provides external hardware (a pull-up resistor or other device) to put the pin in a defined state. Otherwise unintended entry into ISP mode may occur. Figure 1 shows the boot sequence of the LPC210x devices. 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 4 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility Fig 1. Boot process flowchart. 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 5 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility 3. Details of the Philips LPC2000 Flash utility This flash utility is available for free download from the Philips website. This software, in combination with the hardware described below, allows for hands-off erasure, uploading, and execution of code. The Philips LPC2000 Flash utility utilizes two, otherwise unused, signals (RTS and DTR) of the PC serial port to control the microcontroller reset and P0.14 pins. The port pin P0.14, if LOW during reset, puts the microcontroller into In System Programming (ISP) mode; this pin has the alternate functions of external interrupt one and general purpose I/O (GPIO). Some details on the associated circuitry will help in understanding how this works. 3.1 Manual entry into ISP mode With jumper J1 removed and jumper J2 in place ISP mode will be entered manually by holding S2 while pressing and releasing S1 (reset). This can become cumbersome and so it is advantageous to use RTS/DTR control of these signals. 3.2 ISP mode entry using DTR/RTS With jumper J1 inserted and jumper J2 removed the reset and P0.14 signals may be controlled by the previously un-used RTS/DTR signals of the PC serial port. In this application both these signals are active HIGH. When RTS is asserted Q2 is turned on and the microcontroller reset is pulled LOW. While the micro is held in reset, DTR is asserted and P0.14 is held LOW. RTS is then brought LOW and so Q2 is turned off. The 10K pull-up resistor releases the RESET signal by pulling it HIGH. The microcontroller is now running in ISP mode. This sequence of ISP mode entry is performed for every operation offered by the Philips LPC2000 Flash Utility. Fig 2. The RTS/DTR control - an example circuit. 10K DTR S2_INT1_ISP D3 1 2 Q2 3 2 1 RST 22K S1_reset 33K D4 1 2 D1 1 2 P2 DSUB 9-R 5 9 4 8 3 7 2 6 1 5 9 4 8 3 7 2 6 1 100n Note: All signals to P2 except DTR and RTS have been omitted for clarity. 33K J2 12 100n RTS Q1 3 2 1 P0.14 22K Vcc J1 12 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 6 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility The main screen of the Flash Utility provides access to most if its functionality. When the “use DTR/RTS…” box (1) is checked then control of reset and P0.14 is done by the utility as described above. If this box is unchecked then ISP mode must be entered manually. If the “execute code after upload” is checked then, after code is programmed into the flash, an extra reset pulse is sent to the microcontroller to reset the part. Since, at this time, P0.14 will be HIGH, the part will execute code in flash after this reset. When the utility connects to the MCB2100 it will attempt to connect at the selected baud rate. The highest baud rate achievable will depend mostly on the frequency of the crystal. Using standard baud rate crystals (e.g. 14.7456 MHz) will increase the maximum baud rate achievable. 3.3 Flash buffer operations The flash buffer operation screen (accessible from the “buffer” pull-down menu) allows functions such as loading a HEX file, downloading from flash, uploading to flash, filling the buffer, saving the HEX file and calculation of the checksum “valid code” vector1. There is also the ability to fill the buffer with a particular value1 and program this buffer to flash. Fig 3. Flash Utility main screen. 1. The valid code vector at 0x14 is merely the two’s complement of the sum of the vector table. By assigning it this value the checksum for the entire vector table is 0x00 which indicates valid flash code. After reset the bootloader will examine this location and, if the value is correct (an indication of valid user code in flash), will execute code out of flash. If the value is not correct the bootloader will enter ISP mode. The Philips LPC2000 Flash Utility will automatically calculate and program this value during an upload to flash. Alternatively the vector calculation may be performed on the contents of flash buffer as shown in the screen-shot below. 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 7 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility 3.4 RAM buffer operations Ram buffer operations (accessible from the “buffer” pull-down menu) are similar to flash buffer operations including the uploading of HEX files etc. Fig 4. Flash buffer screen. 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 8 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility Fig 5. RAM buffer operations. 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 9 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility 4. Hardware 4.1 Keil MCB2100 evaluation board Figure 6 shows an overview of the Keil MCB2100 evaluation board. JTAG port — Connection to JTAG emulator (e.g. Keil ULink). This is a standard JTAG port as outlined in ARM documentation. ETM (Embedded Trace Macrocell) port — Provides interface to emulators with trace capability. P3 and P4, CAN ports — These provide access to the CAN ports (On boards that feature a microcontroller with CAN interfaces). P1 and P2, UARTs — Access to UART0 and UART1. S1 reset — Microcontroller reset. S2 ISP/INT1 — This button pulls the P0.14 pin of the microcontroller LOW, providing either an external interrupt or manual entry into ISP mode. Fig 6. Keil MCB2100 evaluation board overview. 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 10 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility LEDs — buffered with a 74LVC octal buffer, enabled by J6. Potentiometer — Configured as a voltage divider with its output connected to AIN0 via jumper J2. [1] These jumpers supply the voltages to the microcontroller and must be in for normal operation. [2] Remove this jumper when not using ISP. 4.1.1 Enabling ISP mode with the MCB2100 The Keil MCB2100 evaluation board was designed to utilize the RTS/DTR control of reset and P0.14 as featured in the Philips LPC2000 Flash utility. To setup the MCB2100 for ISP programming set the jumpers: J1, J3, J4, J5, J7 and J10. Connect the PC serial port to COM0 of the MCB2100 and start the LPC2000 Flash Utility. Check the “Use DTR/RTS……” box and continue. 4.2 The IAR/Philips LPC210x Kickstart card This evaluation board is populated with an LPC2106 microcontroller and features 2 serial ports, 2 user-defined buttons, 16 fully configurable LEDs, 20-pin JTAG interface connector as well as breakout headers for all pins. Table 1: Keil MCB2100 jumper functions Jumper Function J1 Configures P0.14 for DTR/RTS control of ISP (see ISP section below) J2 Potentiometer/ADC Connect J3[1] 3.3 V enable J4[1] 1.8 V enable J5 3.3 V analog voltage supply enable J6 LED enable J7 Configures P0.14 for external interrupt or manual ISP entry J8 ETM Pins Enable (Pulls TraceSync LOW) J9 JTAG Debug Pins Enable (Pulls RTCK LOW) J10[2] Configures RESET for DTR/RTS control of ISP (see ISP section below) 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 11 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility JTAG port — Connection to JTAG emulator (e.g. JLink). This is a standard JTAG port as outlined in ARM documentation. ETM (Embedded Trace Macrocell) port — Provides interface to emulators with trace capability. P0 and P1, UARTs — Access to UART0 and UART1. RESET — Microcontroller reset. Interrupt0 — This button provides a source for interrupt zero. Interrupt1 — This button pulls the P0.14 pin of the microcontroller LOW, providing either an external interrupt or manual entry into ISP mode. Interrupt2 — This button provides a source for interrupt two. LED jumper block — enables/disables individual LEDs. LEDs — buffered with a LVT16244. Fig 7. IAR/Philips LPC210x Kickstart card. 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 12 of 14 Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility [1] P0.14 and external interrupt one share the same pin; therefore this button may also be used for manual entry into ISP mode by pressing it during a reset. [2] This jumper, when in the JTAG1 position, will cause the microcontroller to enter JTAG debug mode after reset. Therefore, when using ISP, this jumper must be removed or placed in the JTAG2 position. 4.2.1 Enabling ISP mode with the IAR/Philips Kickstart card The Kickstart Card evaluation board was designed to utilize the RTS/DTR control of reset and P0.14 as featured in the Philips LPC2000 Flash utility. To setup the Kickstart Card for ISP programming set the jumpers: JP7, JP8, JP2 and JP4. Remove jumper JP6. Connect the PC serial port to P0 (UART0) of the Kickstart Card and start the LPC2000 Flash Utility. Check the “Use DTR/RTS……” box and continue. Table 2: IAR/Philips Kickstart card jumper functions Jumper Function JP1 Enables external interrupt zero via the push-button JP2 Enables ISP and external interrupt one[1] JP3 Connects P0.9/RxD1 (UART1) to the MAX3232 JP4 Connects P0.1/RxD0 (UART0) to the MAX3232 JP5 Enables external interrupt zero via the push-button JP6 Primary/Secondary JTAG select[2] JP7 Enable DTR/RTS control of P0.14 JP8 Enable DTR/RTS control of RESET Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility 9397 750 13354 © Koninklijke Philips Electronics N.V. 2004. All rights reserved. Application note Rev. 03 — 10 June 2004 13 of 14 5. Disclaimers Life support — These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. When the product is in full production (status ‘Production’), relevant changes will be communicated via a Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Date of release: 10 June 2004 Document order number: 9397 750 13354 Published in U.S.A. Philips Semiconductors AN10302 Using the Philips LPC2000 Flash utility 6. Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 LPC2000 ISP overview . . . . . . . . . . . . . . . . . . . 3 3 Details of the Philips LPC2000 Flash utility. . . 5 3.1 Manual entry into ISP mode . . . . . . . . . . . . . . . 5 3.2 ISP mode entry using DTR/RTS. . . . . . . . . . . . 5 3.3 Flash buffer operations. . . . . . . . . . . . . . . . . . . 6 3.4 RAM buffer operations . . . . . . . . . . . . . . . . . . . 7 4 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4.1 Keil MCB2100 evaluation board . . . . . . . . . . . . 9 4.1.1 Enabling ISP mode with the MCB2100 . . . . . 10 4.2 The IAR/Philips LPC210x Kickstart card . . . . 10 4.2.1 Enabling ISP mode with the IAR/Philips Kickstart card . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13*/

《TMS320F2812与CCS4：官方最新例程解析》 在数字信号处理领域，TI公司的TMS320F2812是一款广泛应用的高性能浮点DSP（数字信号处理器）。它以其强大的计算能力、丰富的片上外设以及灵活的编程特性，深受工程师们的喜爱。配合Code Composer Studio (CCS) 集成开发环境，能为开发者提供高效便捷的编程体验。本文将深入探讨TMS320F2812在CCS4上的最新例程，帮助初学者快速入门。 TMS320F2812的核心特性在于其32位浮点处理器，运行速度高达150MHz，具有出色的浮点运算性能。同时，它内置了多个硬件乘法器和MAC单元，支持快速的数学运算，特别适合实时信号处理应用。此外，F2812还拥有丰富的外设接口，如SPI、I2C、UART等，便于与其他硬件进行通信。 CCS4是TI推出的一款强大的集成开发环境，集成了编译器、调试器、模拟器等功能，为开发者提供了从代码编写、编译、调试到下载的完整流程。此版本更新到官方v120，意味着它包含了最新的优化和修复，能更好地支持TMS320F2812的开发工作。 官方提供的例程是学习和掌握TMS320F2812的重要资源。这些例程涵盖了基础操作、中断处理、外设控制等多个方面，通过阅读和分析代码，开发者可以快速理解DSP的内部工作原理和编程模式。例如，可能包含以下类型的例程： 1. **初始化例程**：展示了如何配置系统时钟、设置中断向量、初始化RAM和Flash等基本操作。 2. **中断服务例程**：演示了中断处理机制，如定时器中断、串口中断等，这对于实时系统的响应至关重要。 3. **外设控制例程**：如ADC采样、PWM输出、SPI通信等，展示了如何使用和配置F2812的各类硬件资源。 4. **数学运算例程**：如滤波、FFT等，突显了DSP的计算优势，适用于信号处理算法实现。 在CCS4中，开发者可以方便地导入和运行这些例程，利用其调试工具进行单步执行、查看变量状态、设置断点等操作，有助于理解程序执行过程。 对于初学者，建议首先从简单的例程入手，如LED闪烁或串口通信，逐步深入到复杂的算法实现。同时，理解例程中的头文件和库文件也至关重要，它们定义了函数原型、数据结构和常量，是构建软件系统的基础。例如，`F2812xxxx.h`是设备头文件，包含了寄存器定义和宏定义；`ti_math.h`包含了TI提供的数学库函数。 TMS320F2812与CCS4的结合，为开发者提供了强大而全面的开发平台。通过深入研究官方例程，不仅能够熟悉硬件特性，还能掌握高效的编程技巧，为实际项目开发打下坚实基础。无论你是刚刚接触DSP的新手，还是寻求提高的资深工程师，这份官方例程都是一份不可多得的学习资料。

如果你的电脑出现没声音等其他异常情况就要使用到戴尔1420声卡驱动。如果安装后仍没有声音，可以试试换个WIN7版本，就正常了。Audio:SIGMATEL STAC 92XX C-Major HD AudioType Driver Version A03For Inspiron:1420, 1520, 1521, 1525, 1526, 1720,欢迎下载体验

联想G470网卡驱动程序，官方最新驱动，是使用本地网络的必备组件，如果发现本地网不能使用的话，那么试着重装这款驱动吧。联想G470这款笔记本的配置是低端的商务笔记本，娱乐功能较低，作为商务办公本可以轻松应对上网和office办公的需求。参数网卡芯片：AR815,欢迎下载体验

戴尔Inspiron N4120 USB3.0驱动程序，相比传统的2.0，传输速度更快，有需要的就下载吧。参数USB3.0芯片：Renesas Electronics USB 3.0 DeviceWIN7驱动版本：02/10/2011,2.0.34.0WIN8驱动版本：暂缺硬件ID：PCI\VEN_1033DEV_0194SUBSYS_0,欢迎下载体验

戴尔Inspiron灵越M4010网卡驱动，官方最新驱动，是连接本地网络的必备驱动，如果你的笔记本无法连接本地网的话，试着重装此驱动，驱动是从官方下载来的，大家可放心下载使用。参数网卡芯片：Atheros AR8152 PCI-E Fast Ethernet ControllerWINXP驱动版本：,欢迎下载体验

戴尔n4050网卡驱动有适合于xp系统和win7系统两款。win7系统直接可打开安装，xp驱动需要手动指定文件位置。网卡芯片：RealtekRTL8111E-VBGigabitEthernetControllerWINXP驱动版本：01/14/2011,5.782.0114.2011WIN7驱动版本：02/16/2011,7.041.0216.2011硬件ID：,欢迎下载体验

沥青级配自动计算软件是一款非常好用且功能强大的集配方的添加、修改、删除、打印和查询为一体的配方计算体系，沥青级配自动计算整个配方过程可以实现最优规划计算，需要此款工具的朋友们可以前来下载使用。 功能介绍 　　1、基本功能：沥青级配的添加计算、复制计算、修改计算和打印等。 　　2、主要功能：矿料化验筛分结果并不是全部包含对应筛孔，而自动生产线工艺中，计量跟踪是以筛孔为依据，这就导致各种矿料配方

QTTabBar，功能强大的资源管理器拓展软件，标签式多窗口管理，同时常规文件具有快速预览功能