/*********************************************************** 实验名称：LCD12864显示汉字示例程序 程序说明：烧好程序，正确插上LCD12864即可观察到LCD上显示的汉字。 注意：USB供电可能不足，这时需要用变压器供电。 ***********************************************************/ /*********************************************************** 模块名称：st7920 并行方式驱动12864液晶驱动 功能概要：st7920显示驱动 完成日期：2008.07.08 驱动芯片：st7920 ***********************************************************/ #include #define uint unsigned int #define uchar unsigned char #define x1 0x80 #define x2 0x88 #define y 0x80 #define comm 0 #define dat 1 sbit RS = P2^0; //H=data; L="command"; sbit RW = P2^1; //H=read; L="write"; sbit E = P2^2; //input enable; sbit PSB= P2^3; //H=并口; L="串口"; sbit RST= P2^5; //Reset Signal 低电平有效 sbit busy=P1^7; //lcd busy bit void wr_lcd (uchar dat_comm,uchar content); void chk_busy (void); void delay (uint us); uchar code tab31[]={ " RF-X1开发板 " " 您学习的首选 " }; uchar code tab32[]={ /*-- 调入了一幅图像：F:\梁\画图\HOCO12832.bmp --*/ /*-- 宽度x高度=128x32 --*/ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x1E,0x00,0x00,0x00,0x00,0x00,0x07,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00, 0x00,0x7F,0x80,0x00,0x00,0x00,0x00,0x18,0x0C,0x00,0x00,0x01,0x00,0x00,0x00,0x00, 0x01,0xFF,0x80,0x00,0x00,0x00,0x00,0x20,0x00,0x00,0x00,0x13,0x10,0x03,0xFE,0x00, 0x03,0xFF,0xC0,0x00,0x00,0x00,0x00,0x58,0x00,0x00,0x00,0x3F,0x30,0x1F,0xFF,0xC0, 0x03,0xFF,0xE0,0x00,0x00,0x00,0x00,0x8C,0x03,0xF0,0x00,0x7F,0xE0,0x7C,0x01,0xE0, 0x03,0xFF,0xF0,0x00,0x00,0x00,0x01,0x36,0x06,0xC0,0x00,0x5F,0xC0,0xFF,0xFC,0x60, 0x01,0xFF,0xF0,0x00,0x00,0x00,0x02,0x1B,0x0F,0x80,0x00,0xFF,0x01,0xFE,0x0F,0x30, 0x00,0xEF,0xF0,0x00,0x00,0x00,0x02,0x6D,0x9F,0x00,0x00,0x3E,0x03,0xFF,0xF1,0x90, 0x00,0xFF,0xF8,0x00,0x00,0x00,0x04,0x36,0xFE,0x00,0x01,0xFF,0x07,0xFF,0xFC,0x90, 0x00,0xEF,0xFF,0xFF,0x80,0x00,0x04,0xDB,0x7E,0x00,0x03,0xFF,0x87,0xFF,0xFC,0xD0, 0x00,0x0F,0xFF,0xFF,0xC0,0x00,0x04,0x6D,0xFC,0x00,0x07,0xFF,0x8F,0xFF,0xFE,0x50, 0x00,0x0