摘要：在分析无刷直流电机（BLDC）数学模型的基础上，提出了一种无刷直流电机控制系统仿 真建模的新方法。在Matlab/Simulink环境下，把独立的功能模块和S函数相结合，构建了无刷直流 电机系统的仿真模型。系统采用双闭环控制：速度环采用离散PID控制，根据滞环电流跟踪型PWM 逆变器原理实现电流控制。仿真和试验结果与理论分析一致，验证了该方法的合理性和有效性。 此方法也适用于验证其他控制算法的合理性，为实际电机控制系统的设计和调试提供了新的思路。 关键词：无刷直流电机；建模；仿真；电流滞环；Matlab

完整扫描版高清《小型交流伺服电机控制电路设计》，不带书签

永磁同步电机控制simulink仿真模型，Simulink永磁同步电机控制仿真系列文章对应资源，本模型实现了永磁同步电机的dq轴电压控制。

直流无刷电机控制器电路板和原理图dxp，采用带位置传感器和不戴位置传感器两种方式 直流无刷电机控制器电路板和原理图dxp，采用带位置传感器和不戴位置传感器两种方式

dsp2812步进电机控制实验程序，适用于新手学习，已调试

STM32无刷电机控制程序，值得下载学习研究。程序详细清楚。

现代永磁同步电机控制原理及MATLAB仿真随书仿真随书程序

无刷直流电机控制原理

STM32电机控制开发包完全版V5.5.1-5.Y.1，2021年5月3日更新。 STM32 Motor Control Software Development Kit (MCSDK) - FULL source code Main Changes Version 5.Y.1 of the Motor Control Software Development Kit (X-CUBE-MCDSK) is a bug fix release of version 5.Y.0. It fixes the following issues: Some Motor Control examples delivered with MCSDK 5.Y.0 would not configure DMA channels properly to work with the new Motor Control and thus with the Motor Pilot. Also, the baudrate of the UART port configured by examples is set to 1,8 Mbps, the same as ST Motor Pilot's default. ACIM motor based examples do not build on 5.Y.0. They build well on 5.Y.1. The descriptions of EVSPIN32F0x inverter boards delivered with the Workbench had wrong DC & AC voltage supply ranges. These have been corrected as follows: Inverter Wrong AC supply range Corrected AC supply range DC supply range EVSPIN32F02Q1S1, EVSPIN32F0251S1 20 - 120 Vac 15 - 120 Vac 20 - 170 Vdc EVSPIN32F06Q1S1, EVSPIN32F0601S1 50 - 280 Vac 35 - 280 Vac 50 - 400 Vdc EVSPIN32F06Q2S1, EVSPIN32F0602S1 50 - 280 Vac 35 - 280 Vac 50 - 400 Vdc EVSPIN32F06Q1S3, EVSPIN32F0601S3 50 - 280 Vac 35 - 280 Vac 50 - 400 Vdc Six-Step High Voltage examples based on the EVSPIN32F0251S1 inverter board were mistakenly not included into 5.Y.0 version. They are in 5.Y.1. The Pilot would fail to update registers values from the embedded application in some situations. In such a case, information like the motor rotation speed, status and error information would not display. Fixed issues with the DAC output feature. Added many signals to the Datalog and the DAC output features. Among them, the observers, encoder and Hall sensors angles. Running the motor in the negative direction on STM32F0 based designs with 1 shunt and Hall sensor configuration may trigger an overcurrent error. Fixed an issue found on ESC G4 and F3 inverter boards with Motor Control Protocol v2. Contents Components Version License Terms Release Note Utilities/PC_Software/STMotorProfiler 1.3.2

渣浆泵电机控制回路的改进.rar