stmf1支持spiflash存储，并通过usb读取

Cyclone10 FPGA读写MP25P16 spiflash实验Verilog源码Quartus17.1工程文件+文档资料,, FPGA为CYCLONE10LP系列中的10CL025YU256C8. 完整的Quartus工程文件，可以做为你的学习设计参考。 module spi_flash_top( input sys_clk, input rst, output nCS, output DCLK, output MOSI, input MISO, input[15:0] clk_div, input[3:0] cmd, input cmd_valid, output cmd_ack, input[23:0] addr, input[7:0] data_in, input[8:0] size, output data_req, output reg[7:0] data_out, output reg data_valid ); localparam S_IDLE = 0; localparam S_SE = 1; localparam S_BE = 2; localparam S_READ = 3; localparam S_WRITE = 4; localparam S_ACK = 5; localparam S_CK_STATE = 6; //present state monitor localparam S_WREN = 7; wire spi_flash_cmd_ack; reg[3:0] sub_cmd; reg sub_cmd_valid; reg[8:0] sub_size; reg[4:0] state,next_state; reg[7:0] state_reg; wire sub_data_valid; wire[7:0] sub_data_in; wire[7:0] sub_data_out; assign sub_data_in = data_in; assign cmd_ack = (state == S_ACK); always@(posedge sys_clk or posedge rst) begin if(rst==1) state <= S_IDLE; else state <= next_state; end always@(*) begin case(state) S_IDLE: if(cmd_valid && cmd == `CMD_BE) next_state <= S_WREN; else if(cmd_valid && cmd == `CMD_SE) next_state <= S_WREN; else if(cmd_valid && cmd == `CMD_READ) next_state <= S_READ; else if(cmd_valid && cmd == `CMD_PP) next_state <= S_WREN; else next_state <= S_IDLE; S_WREN: if(spi_flash_cmd_ack && cmd == `CMD_BE) next_state <= S_BE; else if(spi_flash_cmd_ack && cmd == `CMD_SE) next_state <= S_SE; else if(spi_flash_cmd_ack && cmd == `CMD_PP) next_state <= S_WRITE; else next_state <= S_WREN; S_BE: if(spi_flash_cmd_ack) next_state <= S_CK_STATE;//读取状态寄存器 else next_state <= S_BE; S_SE: if(spi_flash_cmd_ack) next_state <= S_CK_STATE;

华邦电子-SPIFLASH-W25Q16 datasheet

GD35B127D芯片手册，BIOS芯片用

STM32 模拟SPI驱动 W25Q

STM32F407IGT6单片机SPI FLASH读写实验例程5个合集KEIL工程源码+文档说明: SPI-串行Flash小数存储.rar SPI-串行Flash整数存储.rar SPI-串行Flash读写测试.rar SPI-基于串行Flash的FatFs功能使用.rar SPI-基于串行Flash的FatFs文件系统.rar

本文对AT24系列存贮器和AT89系列单片机的特征及总线状态作为介绍，并以AT24C01与AT89C2051为例详细描述了通用存贮器IC卡的工作原理及用单片机进行ic卡读写器一系列操作的基本电路连接和软件编程的设计方法。

24c02读写程序绝对好用的 DS18B20测温 通过RS232总线与PC进行通信的测试程序(c语言) 单片机模拟I2C读写E2PROM 51单片机与串口通信(含代码)

一款批量SPI烧录器的原理图以及控制程序，方便批量烧写字库。语音，等文件记录。可做系统初始化使用。包含原理图以及控制程序

华邦w25x16 SPIFlash Read ID FPGA(EP4CE6)实验Verilog逻辑源码Quartus工程文件+文档说明资料，FPGA为CYCLONE4系列中的EP4CE6E22C8. 完整的工程文件，可以做为你的学习设计参考。 **------------------------------------------------------------------------------------------------------ ** Modified by: ** Modified date: ** Version: ** Descriptions: Read the Device ID of the W25X16 Flash ** **------------------------------------------------------------------------------------------------------ ********************************************************************************************************/ module W25X16 ( //input signal input sys_clk , input sys_rst_n , input W25X16_DO , //output signal output reg W25X16_CS , output reg W25X16_CLK , output reg W25X16_DIO , output reg [7:0] LED ); //reg define reg [5:0] counter ; reg [5:0] clk_cnt ; reg [15:0] shift_buf ; //wire define wire div_clk1 ; wire div_clk2 ; /******************************************************************************************************* ** Main Program ** ********************************************************************************************************/ //creat a clock about 1MHz always @(posedge sys_clk or negedge sys_rst_n) begin if ( sys_rst_n ==1'b0 ) clk_cnt <= 6'b0; else clk_cnt <= clk_cnt + 1'b1; end assign div_clk1 = clk_cnt[5]; assign div_clk2 = ~clk_cnt[5]; //get a counter that width is 6 bits always @(posedge div_clk1 or negedge sys_rst_n) begin if ( sys_rst_n ==1'b0 ) counter <= 6'b0; else counter = 8 && counter <= 58 ) W25X16_CS <= 1'b0;